Complete Repair Parts HUSQVARNA 365 362 371 372 372XP ENGINE MOTOR CRANKCASE CYLINDER PISTON CRANKSHAFT CHAINSAW Item NO.: CS36520A

Very satisfied and fast shipping

Received the kit approximately 2 weeks ago - spent a few hours putting it together and just finished breaking it in with 25:1 fuel/oil mix. I must say that I am thoroughly impressed with the quality of this machine. It was relatively easy to put together (like others, I wish the oil seals were not preinstalled because you have to remove them when putting the case together), and it has been going above and beyond in terms of expectations. Incredible power and starts within 3 or 4 pulls. I highly recommend this kit to any chainsaw/husqvarna enthusiast

Ive had no problems

Bought one a couple of months ago, seen a lot of favourable reviews so for the price why not. Arrive to NZ within the nine days specified, well wrapped and undamaged. Used all parts as supplied except gudgeon circlips were wrong size (replaced with OEM) and no o ring for the pto sleeve (1x.6mm) apparently this does not come with the kit?. Why? The squish was 50 thou with the base gasket so trimmed 27 thou off the barrel flange to give me 23 thou. Started after six or seven pulls, ran it a little rich for a tank or two 13000rpm then leaned a little to give a very strong good feeling saw. After five tanks I reckon this will give my 562xp a good run for its money. Enjoyed putting this saw together, will do another when I get time. Only time will tell long term but components all look fairly robust so would expect to get a lot of work done.

I assembled a saw using this kit and a BB 52mm kit, with no base gasket.
The saw kit had a flywheel that did not have enough contact between crankshaft and the flywheel, but HUZTL did send a new one. Thanks HUZTL.
The saw needs a o-ring 15 x 0.6 mm # 503 26 30 19, between the bearing and sleeve ( PJ36525 ) on the clutch side.
I did use a 13 x 1 mm o-ring.
The compression very very high.
It is a really a good and strong saw. It has used 20 tanks of fuel at this time.
It is a favorite among my saws.

Great kit. All the parts were there , still going STRONG after two firewood seasons. Love it

This saw was a very good buy!!! I loved putting it togther and using!!! Runs great!! It will be buying a couple more of them!!

kit had all parts included and was fun to build, went together without a hitch, used some videos on youtube to help assembly. saw runs and cut great

Bonjour ,

J'ai acheter cette tronçonneuse en kit et franchement , pour le prix je ne suis vraiment déçu cette machine fonctionne véritablement bien .

Les seuls petits points négatifs sont :
- la valve de décompression qui n'est pas bien étanche , facile a réparé avec un bouchon .

- les joints spi de vilebrequin qui sont arrivés montés sur les carters moteur mais qui était craqués j'ai du en acheter des OEM ( 30 € , environ ) .

- Et le lanceur qui avais le ressort détendu .

Mis à part ça rien a signalé pour le moment .

Pour 184,43 € en promotion , je ne suis vraiment pas déçu de mon achat !

Vous pouvez y allez les yeux fermés .

Je suis le premier français a mettre un avis sur les kit de montage de tronçonneuse huztl , je tiens donc a vous dire que je n'ai rien reçu pour promouvoir leurs machines .

Tout ce qui est rédigé plus haut est la stricte vérité.

Merci .
Et merci huztl je commanderais d'autres kits dans le futur .

brought a 365 husqvarna easy to assemble 2 pulls and the pull start broke had another pull start,apart from that chainsaw runs well cut about 4 ton of wood no problem at all

brought a 365 husqvarna easy to assemble 2 pulls and the pull start broke had another pull start,apart from that chainsaw runs well cut about 4 ton of wood no problem at all

Excellent kit, I've built quite a few of these kit saws from Huztl, and in my opinion this kit is the best as far as quality of parts goes, everything fit the way it should, packaging is great, all parts are separated to make for fast assembly.

I've run the saw for about a week now after assembly and it is fantastic, good power smooth operation, no vibration.

Highly recommend this kit.

2nd saw I've built from hutzl great kit went together with no issues like stated in other comments they don't have the o-ring that goes behind the oiler looking forward to getting other kits soon

372 kit., very impressed all the parts were their ecxept one o ring very critical part oem # 503-26-30-19 its a must item.other than a good cleaning some lube and THREAD LOCKER all went well,removed starter dogs lubed and thread locker on bolts checked clearances also. started and run very good quality is far better than expected. great kit highly recommend.good value also.

I have assembled the 372xp and run 4 tanks thru it.

It starts very well so far and has good power, but I have it de-tuned so I am not sure what the final power will be.

There were a number of minor issues with the assembly and parts:

The box was missing a small o-ring for the clutch side and small plastic tubes for the carb mounting bolts. Huztl offered to send these for free with my next order.

The metal clip for the oil pump was not shaped correctly, but was easily reshaped.

The rubber grommet for the oil tube was too small and had to be enlarged.

The idle adjustment screw on the carburetor does not increase the idle, even when screwed completely in, though the saw idles well.

The air filter did not fit tightly and needed some tape/slight modification to work properly.

The bar sent with the saw had some small bends that need correction.

The muffler bracket and a couple of the large plastic parts were very slightly mis-shaped and took some twisting to mount properly.

Overall, the saw is a good deal for the price. I think Huztl is working to perfect these issues and I will be buying more from them and recommending them to friends.

Purchased this saw kit and 372 big bore cylinder kit in my first order from Huztl and was far better quality than I anticipated. Assembles quick with great fit and quality parts. Fun to put together. Both cylinders coating had no flaws. I will most likely sell my oem 365 and keep this for myself. Also fast shipping, received in eight days with good tracking available. be back for more purchases soon.

Quality is better than anticipated. Machining and fit were excellent along with plastic part quality.
No modifications needed on assembly for fit. Saw started on third pull and runs VERY well!!!
A lot of bang for the buck here!!!!

Video link left a review separate https://youtu.be/zl2b4rRLZKs

Excellent quality parts plastics even feel great really close to OEM in my opinion very good option if you are mechanically inclined had an issue with an air leak in the case crank case seal contacted them was patient went back-and-forth showing I knew what I was talking about and explaining the problem they sell replacement parts which solve the problem sol has great throttle response and cuts very well have two tanks through it hopefully it will build strength as it goes compression tester compression is holding at 120 PSI hopefully it will build more as it breaks and from what I have read on Huska Varna's website it is pretty common for them to start around 120 or 130 fires up no matter what cold or warm easy cold in South Dakota which gets really cold fires on three poo at 120 PSI hopefully it will build more as it breaks and from what I have read on Huska Varna's website it is pretty common for them to start around 120 or 130 fires up no matter what cold or warm easy cold in South Dakota which gets really cold fires on three pulls when warm fires with one extremely strong saw I am only running a 20 inch bar and chainhain full comp 35 when warm fires with one extremely strong saw I am only running a 20 inch bar and chain fall camp degrees low rakers kinds granny Burns through two foot ash and cherry like soft wood bought an extra cylinder and playing around with some porting too bad I didn't buy another case and set up to finish putting it together I will up lo too bad I didn't buy another case and set up to finish putting it together ad some videos on you tube and would love to test the big bore kit if you feel like sending one thanks again

This is a pretty awesome kit it has all but one piece needed to assemble the saw the quality is better than I expected every piece had good fitment and the machine work was really good. I was told that this kit would come with an open ported cylinder but the one I received was a closed port cylinder with good machine work, the nicasil had complete coverage and the port openings were symmetrical and square. The only item that was missing was an o-ring seal part# 503 26 30-19 that goes on the crank (pto side) before the crankcase seal sleeve is installed under the clutch. If this o-ring is not installed you will have a vacuum/pressure leak that will result in a lean run condition and then cylinder/piston failure. All the plastic was of good quality as well. One piece of plastic the spark plug/air filter cover was a slightly darker color of orange. This saw does not have a primer bulb set up so to make start up easier just use a small amount of 2 cycle mix in the carb and it starts right up. I would not run gas oil mix any leaner than 32:1 might even consider 28:1. This saw seems to have great power great throttle response and good idle characteristics.
At $150 Dollars this saw is a great deal.